- Fully Programmable 50MHz Arm® Cortex® -M0
- Integrated 70V DC/DC Buck or SEPIC controller
- Integrated 70V/1A Gate Drivers
- Integrated PGA (3 Differential, 4 Single-ended)
- Integrated DACs and Comparators
- UART, I2C and SPI serial interfaces
- Extremely low total hibernate mode
- IEC/UL60730 Class B optimized
- Minimal external components
- 6x6mm, 48-pin QFN
The PAC5225 belongs to Active-Semi’s Power Application Controller® (PAC) family. The PAC family of products are highly-optimized SOC devices that can implement BLDC or PMSM programmable motor controller and driver in a single integrated IC. The PAC5225 integrates a FLASH-based MCU, Power Management , High-side and low-side Gate Drivers and Signal-Conditioning components in a single product.
The PAC5225 is optimized for battery-powered BLDC motor control applications up to 48V that implement IEC/UL60730 Class B Safety.
The PAC5225 contains a 50MHz Arm® Cortex®-M0 with 32kB of FLASH that can be used to implement high-performance motor control and supervisory applications. The MCU also contains motor control peripherals such as 10b 1MSPS dual auto-sequencer ADC, PWM timers with hardware dead-time insertion, etc. The Multi-Mode Power Manager™ (MMPM) contains a Buck or SEPIC DC/DC controller and power management components for powering the IC and other PCB system power supplies. The Application-Specific Power Drivers provide integrated gate drivers for use with an external inverter. The Configurable Analog Front-End™ (CAFE) provides signal-chain components such as differential and single-end amplifiers, comparators and DACs.
Advantages of our Intelligent Motor Control
|Programmable 32-bit MCU||Allows implementation of high-performance advanced control algorithms such as Field Oriented Control (FOC), Sensorless BEMF, Sensored BLDC and serial communications protocols|
|Integrated Power Manager||Removes the need for an external 600V DC/DC Controller. Provides 5V/200mA system supply for additional PCB peripherals. Integrates all power rails for MCU, FLASH, Analog and gate drivers|
|Integrated Gate Drivers||Removes the need external open-drain driver circuits|
|Integrated Signal Chain||Allows integrated Current, Voltage and Temperature sensing and protection using integrated Differential and Single-ended Programmable-Gain Amplifiers, comparators and DACs|
|Lowest standby power||Allows 18µA Iq for standby-mode|
|IEC/UL60730 Class B Optimization||Allows implementation of the IEC/UL60730 Class B standard without additional system cost for PCB components|
- PAC52XX PCB Layout Guidelines
- PAC52XX Configuring the CAFE for Different Control Topologies
- PAC52XX Multi Mode Power Manager
- PAC52XX FLASH Memory Controller Configuration
- PAC52XX Temperature Sensing and Protection
- PAC52XX Using Watchdog SysTick and GP Timers
- PAC52XX Clock Control Firmware Design
- PAC52XX GPIO Peripheral Firmware Design
- Converting Firmware to Code and IAR
- PAC52XX Writing Configuration Parameters to Flash
PAC5225 is supported by the EP5223LVM1-1 evaluation board.
PAC5225 has hardware support to enable Class B certification.
Supporting Evaluation Tools
The ET-UARTSWD adapter is the preferred adapter for evaluation of PAC devices/firmware and combines a USB to UART adapter with SWD debugger connector adaptation into a single board with isolation. The ET-UARTISO-1 adapter provides only the USB to UART adapter with isolation for Active-Semi application GUI communications.
|The ET-UARTISO-1 adapter is a USB to UART adapter for Active-Semi application GUI communications with the PAC device UART, and can be used for evaluation and debugging of PAC applications.|
|Buy it at these partners|
PAC5xxx Flash Programmer Tools
Active-Semi has partnered with Flash Programmer solution providers to support our Intelligent Motor Control PAC product families.
These proven tools are suitable for emerging and high volume product manufacturing.
Both package level (socketed) and board level Flash programming solutions are available.
Active-Semi will support other vendors familiar with Arm® Serial Wire Debug (SWD) protocol to add PAC product compatibility on their existing Flash programmer platforms.
For more details contact firstname.lastname@example.org
Installer for the PAC52XX BLDC application firmware, which implements sensored BLDC and sensorless BEMF motor control on all members of the PAC52XX family. The installer contains example application source code, Windows graphical user interface (GUI), and documentation to allow the user to configure the system to work with their target motor. Project files for IAR Systems Embedded Workbench for ARM (EWARM) and Keil uVision are included.
Installer for the PAC FOC application firmware designed to show case motor control using sensorless Field Oriented Control (FOC) on all PAC devices. The installer contains example FOC application source code, Windows graphical user interface (GUI), and documentation to allow the user to configure the system to work with their target motor. Project files for IAR Systems Embedded Workbench for Arm® (EWARM), Keil uVision and Eclipse are included. The FOC application provides a configurable set of features to meet many different application requirements such as sensorless position/speed estimator, start-in-motion (SIM), three or single shunt operation, open phase detection (OPD), field weakening and others.
Installer for the PAC52XX Software Development Kit (SDK) that provides register level definitions and peripheral driver APIs for developing ARM M0 application firmware on all PAC52XX devices. The PAC52XX SDK is a unified SDK that supports Keil µVision IDE, IAR Systems Embedded Workbench for ARM (EWARM) IDE, and GCC tool chains.
Installer for the PAC52xx Example Code that provides a simple source code example for getting started with the following IDE projects: Keil MDK (µVision), IAR Systems Embedded Workbench for ARM (EWARM), and Eclipse.
PAC52xx IDE Support
Development of application firmware for PAC52XX Arm® Cortex® M0 is made easy with standard integrated development environments (IDEs). Several of the most popular IDEs contain support for PAC52XX devices including Keil uVision, and IAR Systems Embedded Workbench for Arm®. Eclipse development is possible using J-Link by downloading and installing the “Eclipse with PAC support” package.
PAC52XX Keil IDE Guide
|Guide for installing Keil uVision for development of PAC52XX application firmware.|
Keil PAC52xx .pack v1.0.9 to v2.0.0 upgrade
|Guide for upgrading the Keil uVision PAC52XX pack from v1.0.9 to v2.0.0.|
PAC IAR Support
|PAC IAR Systems Embedded Workbench IDE installation guide and patches.|
Eclipse with PAC support
Version: v1.1.0 2019-03-27
|Installer for Eclipse and supporting plugins for development on the PAC family of devices.|
Segger J-Link Support
|PAC support files for Segger J-Link debuggers.|