- Fully Programmable 32-bit MCU
- Integrated 70V DC/DC Buck or SEPIC controller
- Integrated 70V/1A Gate Drivers
- Integrated PGA (3 Differential, 4 Single-ended)
- Integrated DACs and Comparators
- UART I2C and SPI serial interfaces
- Extremely low total hibernate mode
- Minimal external components
- 6x6mm, 48-pin QFN
The PAC5223 belongs to Active-Semi’s broad portfolio of full-featured Power Application Controller® (PAC) products that are highly optimized for controlling and powering next generation smart energy appliances, devices, and equipment. These application controllers integrate a 50MHz ARM® Cortex®-M0 32-bit microcontroller core with Active-Semi’s proprietary and patent-pending Multi-Mode Power Manager™, Configurable Analog Front EndTM, and Application Specific Power DriversTM to form the most compact microcontroller-based power and general purpose application systems. The PAC5223 microcontroller features up to 32kB of embedded FLASH and 8kB of SRAM memory, a high-speed 10-bit 1µs analog-to-digital converter (ADC) with dual auto-sampling sequencers, 5V/3.3V I/Os, flexible clock sources, timers, a versatile 14-channel PWM engine, and several serial interfaces.
Advantages of our Intelligent Motor Control
|Fully Programmable 32-bit MCU||Flexible implementation of motor control algorithms. Active-semi provides a software library to enable quick startup and time to market.|
|Integrated Power Manager||Integrated DC/DC to enable AC/DC Flyback topology a DCDC Buck or SEPIC
Integrated LDOs for system supplies, Integrated voltage and current protection
|Integrated Analog Front End||With fully integrated High and Low-Side Gate Drivers, integrated Power Supply Controller to reduce external component count and signal conditioning|
|Lowest Standby Power||Total system hibernate mode allows extremely low quiescent operation for the total solution|
- PAC52XX PCB Layout Guidelines
- PAC52XX Configuring the CAFE for Different Control Topologies
- PAC52XX Multi Mode Power Manager
- PAC52XX FLASH Memory Controller Configuration
- PAC52XX Temperature Sensing and Protection
- PAC52XX Using Watchdog SysTick and GP Timers
- PAC52XX Clock Control Firmware Design
- PAC52XX GPIO Peripheral Firmware Design
- Converting Firmware to Code and IAR
- PAC52XX Writing Configuration Parameters to Flash
Active-Semi’s EP5223LVM1-1 development platform is a complete hardware solution enabling users not only to evaluate the PAC5223 device, but also develop power applications revolving around this powerful and versatile ARM® Cortex®-M0 based mirco-controller. The module contains a PAC5223 Power Application Controller (MCU) and its internal peripherals once power is applied.
To aid in the application development the EP5223LVM1-1 offers access to each and every one of the PAC5223 device’s signals by means of a series of female header connectors.
The EP5223LVM1-1 can be used with various Graphical User Interface (GUI) software suites to externally control particular application’s features over the PAC5223 UART I/F. The ET-UARTISO-1 is a USB to UART adapter that can provide the required PC connectivity. If CooCox CoIDE or CoFlash are desired for development, the ET-COLINK-1 adapter is an inexpensive option for SWD Flash programming and debugging.
RD5223PT Battery operated Power Tool Reference Design
The EP5223PT1-1 reference design shows how the PAC5223 can be used to implement a high-current power tool application such as a battery-operated drill in a compact form-factor. This design is a 2.5cmx6cm PCB that can support up to 25A RMS and a peak current of 200W to 300W with the proper heat-sinking. Since the PAC5223 provides just the controller function, by selecting different FETs and component values, the power output of this design could be increased to much higher levels for different application requirements.
“TinyBLDC” reference design
The “TinyBLDC” reference design shows how the PAC5223 may be used to implement an Embedded Speed Controller (ESC) for drone and RC applications. This reference design supports BLDC with a single current shunt for motor current and can run up to 20V with an RMS output current of 17A. Since the PAC5223 provides just the controller function, by selecting different FETs and component values, the power output of this design could be increased to much higher levels for different application requirements.
“TinyFOC” reference design
The “TinyFOC” reference design shows how the PAC5223 may be used to implement an Embedded Speed Controller (ESC) for drone and RC applications. This reference design supports FOC with three phase current shunts for motor current and can run up to 20V with an RMS output current of 17A. Since the PAC5223 provides just the controller function, by selecting different FETs and component values, the power output of this design could be increased to much higher levels for different application requirements.
Supporting Evaluation Tools
The ET-COLINK-1 adapter allows the user to program and perform source level debugging of the target device using SWD from a PC. This adapter is required when using the CooCox CoIDE for development. This IDE and adapter will allow the user to program FLASH on the device, as well as perform source-level debugging of the application.
The ET-UARTISO-1 adapter allows the user to connect the graphical user interface (GUI) to the target board via USB. The adapter allows the user to access the UART serial channel on the PAC device, so that the GUI may be used for evaluation and debugging of an operating system.
Installer for the PAC52XX BLDC application firmware, which implements sensored BLDC and sensorless BEMF motor control on all members of the PAC52XX family. The installer contains example application source code, Windows graphical user interface (GUI), and documentation to allow the user to configure the system to work with their target motor. Project files for CooCox CoIde, IAR Systems Embedded Workbench for ARM (EWARM) and Keil uVision are included.
Installer for the PAC52XX FOC application firmware designed to show case motor control using sensorless Field Oriented Control (FOC) on all members of the PAC52XX family. The installer contains example FOC application source code, Windows graphical user interface (GUI), and documentation to allow the user to configure the system to work with their target motor. Project files for CooCox CoIde, IAR Systems Embedded Workbench for ARM (EWARM) and Keil uVision are included. The FOC application provides a configurable set of features to meet many different application requirements such as sensorless position/speed estimator, start-in-motion (SIM), initial position detection (IPD), open phase detection (OPD), field weakening and others.
PAC52xx Software Development Kit
Installer for the PAC52XX Software Development Kit (SDK) that provides register level definitions and peripheral driver APIs for developing ARM M0 application firmware on all PAC52XX devices. The PAC52XX SDK is a unified SDK that supports Keil µVision IDE, IAR Systems Embedded Workbench for ARM (EWARM) IDE, and GCC tool chains.
PAC52XX IDE Support
Development of application firmware for PAC52XX ARM Cortex® M0 is made easy with standard integrated development environments (IDEs). Several of the most popular integrated IDEs contain support for PAC52XX devices including Keil uVision, IAR Systems Embedded Workbench for ARM, and Coocox CoIDE.
Guides for installation of each of these IDEs
|PAC52XX_Keil_IDE_Guide||Guide for installing Keil uVision for development of PAC52XX ARM Cortex M0 application firmware.|
|PAC52XX_Keil_IDE_Upgrade_v1.0.9_pack_to_v2.0.0_pack||Guide for upgrading the Keil uVision PAC52XX .pack from v1.0.9 to v2.0.0.|
|PAC52XX_IAR_IDE_Guide||Guide for installing IAR Systems Embedded Workbench IDE for development of PAC52X ARM Cortex M0 application firmware.|
|PAC52XX_CooCox_IDE_Guide||Guide for installing CooCox CoIDE for development of PAC52XX ARM Cortex M0 application firmware.|